Model NO.: ZJWZ-1000
Model NO.: ZJWZ-1000
1. Complete the bulge tube, ofexpand mouth and turn over the
Side complete setcraft procedure automatically;
2. Japan Mitsubishi or OMRON PLC computer control, working
Procedure show by LCD;
3. Adoption the liquid presses to gather the whole piece equiping
Withoil grind valve piece, the oil temperature controls auto matically;
4. There is two kinds of models can be provided as choice;
5. Bulge tube length 200-600 MMS four row, each line up 24 bore;
6. Blage tube length 300-1200 MMS four row, each line up 40 bore;
7. Blage tube length 300-3000 MMS six row, each line up 60 bore.
Standard Accessories:
1)Â Â Â Â Â Mandrel commissioning/releasing deviceÂ
2)Â Â Â Â Â Middle base plate & accessoriesÂ
3)Â Â Â Â Â Expanding accessories
4)Â Â Â Â Â Pattern drawing plate accessories
5)Â Â Â Â Â Base plate to Hair-pin receiver
6)Â Â Â Â Â Expanding adjusting device
Stand tools including:
| Â |
 |
Q'ty |
| 1 |
Expand rod 1000mm |
144 |
| 2 |
Expand head ( called bullet also) |
144 |
| 3 |
Expand sleeve |
144 |
| 4 |
Flaring sleeve receiving rod |
144 |
| 5 |
Knock-out sleeve |
48 |
| 6 |
Level insert acceptor (U) |
36 |
| 7 |
Slanting insert |
72 |
Spare parts will be affixed with machine as above form, If more parts needed, the above price should be followed.
Â
Details:
Structure Introduction:
1. The machine is horizontal collocation, load and unload workpiece by manual, expanding, flaring and folding can be finished in one cycle.
2. Length adjustment of second expansion is done by motor reducer, sprocket and chain which drive guide screw to rotate synchronous , guide screw connect with coder and the length change can be showed on the PLC terminal display.
3. Using Pre-pressing pneumatic cylinder to clamp the workpiece
4. Expanding bar quick connect, pneumatic lock and expanding bar protective device are fixed on the machine. The protective device will stop operating automatically to avoid damaging expanding bar if expanding bar run into unexpected case and bend.
5. Accept seat is provided with locking structure, which will not be pulled out when unload and it is also convenient for changing the specification.
Main Technical Parameter:
Tube specification: 8mm*.0.4mm , 6 row, 24holes.
Max. length of the tube (Finished workpiece length): 1000mm.
Max width of workpiece: 980mm
Maximum expanding power: 30T
Work speed:
fast advance:Approximately 5m/min;
slow advance:0.85M/min;
Return speed:8m/min  Â
Oil pump :Double-pump supply . Big pump 116 liters/minute, Small pump 25 liters/minute
Pump motor : 11kw
Electrical Supply: 3 phase 4 wires, voltage is 380v.
Machine Component Selection:
1. The machine adopts "OMRON"PLC controller, main electric components (limit switch, switch button, air switch, contactor, relay, thermal relay) are imported in Japanese,electrical control system conforms to our national related safety standard.
2. Expander rod is made from 65Mn Carbon Manganese steel, use hard alloy expander rod, Gcr15 hardened final expander, final expander rod. Stripper.
3. Cylinder is imported seal packing.
4. Hydraulic pressure pump valve uses domestic (buxin, yuchi/youyan ) or Japan "YUKEN"origin product,2 kinds for choice.
5. There are domestic or imported (Japan SMC ) two kinds of pneumatic components for choice.
Â
Â
1. Complete the bulge tube, ofexpand mouth and turn over the
Side complete setcraft procedure automatically;
2. Japan Mitsubishi or OMRON PLC computer control, working
Procedure show by LCD;
3. Adoption the liquid presses to gather the whole piece equiping
Withoil grind valve piece, the oil temperature controls auto matically;
4. There is two kinds of models can be provided as choice;
5. Bulge tube length 200-600 MMS four row, each line up 24 bore;
6. Blage tube length 300-1200 MMS four row, each line up 40 bore;
7. Blage tube length 300-3000 MMS six row, each line up 60 bore.
Standard Accessories:
1)Â Â Â Â Â Mandrel commissioning/releasing deviceÂ
2)Â Â Â Â Â Middle base plate & accessoriesÂ
3)Â Â Â Â Â Expanding accessories
4)Â Â Â Â Â Pattern drawing plate accessories
5)Â Â Â Â Â Base plate to Hair-pin receiver
6)Â Â Â Â Â Expanding adjusting device
Stand tools including:
| Â |
 |
Q'ty |
| 1 |
Expand rod 1000mm |
144 |
| 2 |
Expand head ( called bullet also) |
144 |
| 3 |
Expand sleeve |
144 |
| 4 |
Flaring sleeve receiving rod |
144 |
| 5 |
Knock-out sleeve |
48 |
| 6 |
Level insert acceptor (U) |
36 |
| 7 |
Slanting insert |
72 |
Spare parts will be affixed with machine as above form, If more parts needed, the above price should be followed.
Â
Details:
Structure Introduction:
1. The machine is horizontal collocation, load and unload workpiece by manual, expanding, flaring and folding can be finished in one cycle.
2. Length adjustment of second expansion is done by motor reducer, sprocket and chain which drive guide screw to rotate synchronous , guide screw connect with coder and the length change can be showed on the PLC terminal display.
3. Using Pre-pressing pneumatic cylinder to clamp the workpiece
4. Expanding bar quick connect, pneumatic lock and expanding bar protective device are fixed on the machine. The protective device will stop operating automatically to avoid damaging expanding bar if expanding bar run into unexpected case and bend.
5. Accept seat is provided with locking structure, which will not be pulled out when unload and it is also convenient for changing the specification.
Main Technical Parameter:
Tube specification: 8mm*.0.4mm , 6 row, 24holes.
Max. length of the tube (Finished workpiece length): 1000mm.
Max width of workpiece: 980mm
Maximum expanding power: 30T
Work speed:
fast advance:Approximately 5m/min;
slow advance:0.85M/min;
Return speed:8m/min  Â
Oil pump :Double-pump supply . Big pump 116 liters/minute, Small pump 25 liters/minute
Pump motor : 11kw
Electrical Supply: 3 phase 4 wires, voltage is 380v.
Machine Component Selection:
1. The machine adopts "OMRON"PLC controller, main electric components (limit switch, switch button, air switch, contactor, relay, thermal relay) are imported in Japanese,electrical control system conforms to our national related safety standard.
2. Expander rod is made from 65Mn Carbon Manganese steel, use hard alloy expander rod, Gcr15 hardened final expander, final expander rod. Stripper.
3. Cylinder is imported seal packing.
4. Hydraulic pressure pump valve uses domestic (buxin, yuchi/youyan ) or Japan "YUKEN"origin product,2 kinds for choice.
5. There are domestic or imported (Japan SMC ) two kinds of pneumatic components for choice.
Â
Â
Passenger Elevator
Mirror Etched Lift,Passenger Lift,Passenger Elevator
Bolt Elevator Co., Ltd. , http://www.jn-elevator.com